Friday, December 19, 2025

Cessna 172N Skyhawk, N80FP, fatal accident occurred on November 24, 2025, near New Orleans, Louisiana

  • Location: New Orleans, LA 
  • Accident Number: CEN26FA051 
  • Date & Time: November 24, 2025, 18:24 Local 
  • Registration: N80FP 
  • Aircraft: Cessna 172N 
  • Injuries: 2 Fatal 
  • Flight Conducted Under: Part 91: General aviation - Instructional 
https://data.ntsb.gov/carol-repgen/api/Aviation/ReportMain/GenerateNewestReport/202066/pdf

https://registry.faa.gov/AircraftInquiry/Search/NNumberResult?nNumberTxt=N80FP

On November 24, 2025, at 1824 central standard time, a Cessna 172N airplane, N80FP, was destroyed when it was involved in an accident near New Orleans, Louisiana. The flight instructor and pilot receiving instruction were fatally injured. The flight was operated as a Title 14 Code of Federal Regulations Part 91 instructional flight.

It was reported that the purpose of the flight was instrument flight instruction for the private pilot. ADS-B data showed that the airplane departed from runway 14 at the Gulfport-Biloxi International Airport (GPT), Gulfport, Mississippi, about 1743. The airplane made a right turn after departure, climbed to about 4,000 ft mean sea level (msl) and traveled west-southwest until 1759. It then turned to a westerly heading and descended to about 2,000 ft msl About 1814, the airplane turned to a heading of approximately 250° before turning to a heading of about 180° about 1817. The airplane was on a heading consistent with a straight-in approach for runway 18R at the Lakefront Airport (NEW), New Orleans, Louisiana. The airplane began descending about 1820, when the airplane was about 6 nautical miles (nm) from NEW, about 1823:02, the airplane began a tight descending left turn that lasted about 27 seconds until the last recorded position at 1823:30. The final recorded position was about 3.7 nm from the approach end of runway 18R at NEW. The final ADS-B position was about 500 ft from where the wreckage of the airplane was located.

Preliminary air traffic control (ATC) information indicated that the flight was on an instrument rules flight plan and was in communication with ATC controllers at the time of the accident. The flight had been cleared for the instrument landing system (ILS), runway 18R approach to NEW.

The reported weather conditions at NEW around the time of the accident included: Wind 130° at 11 kts, visibility 10 statute miles, ceiling 800 ft broken, temperature 22°C, and dewpoint 21°C.

On the day of the accident, sunset occurred at 1700 and the end of civil twilight was at 1726. The moonrise was at 1023, moonset was at 2036, and 17% of the moon’s visible disk was illuminated.

The airplane impacted the waters of Lake Pontchartrain and broke apart on impact. The wreckage was located and then recovered from the lake on December 3, 2025, and transported to an off-site facility for examination. Most of the airplane wreckage was recovered including the majority of the fuselage, wings, tail surfaces, engine and propeller. Some small portions of the airframe were not recovered. The airplane’s empennage, including the elevators and rudder remained attached to the aft fuselage. Continuity of the empennage flight controls was verified to the cockpit controls. The airplane’s wing had separated from the bulk of the fuselage. Portions of all wing flight control surfaces were recovered and remained attached to separated portions of the wing structure. Flap control continuity was verified. Aileron control continuity was verified with all cable breaks exhibiting overload signatures or having been cut during the recovery of the airplane. The forward main wing spars were continuous from root to tip. The left wing strut remained attached to the left wing spar at its upper end. The lower end of the strut was separated from the fuselage with a portion of the fuselage still attached to the bottom of the strut. The right wing strut had separated from the wing spar. The upper strut fitting remained attached to the wing spar. The lower end of the strut was separated from the fuselage with a portion of the fuselage still attached to the bottom of the strut.

The airplane’s engine was manually rotated, and compression was verified on all cylinders. The forward two cylinder pushrods and pushrod tubes had separated from the engine and were not recovered. Movement of the rear cylinder rocker arms and forward cylinder tappets was verified with crankshaft rotation. The magnetos were water logged and would not produce spark when rotated. The magnetos were partially disassembled and the contact points were observed to open end close as expected upon rotation of the input shafts. The dry vacuum pump was removed, and the input coupling was sheared. The rotor core was cracked, and the vanes were intact.

SilverLight American Ranger AR-1, N529MW, accident occurred on December 16, 2025, at Colorado Air and Space Port (CFO/KCFO), Denver, Colorado

This is preliminary information, subject to change, and may contain errors. Any errors in this report will be corrected when the final report has been completed.

https://registry.faa.gov/AircraftInquiry/Search/NNumberResult?nNumberTxt=N529MW

- History of Flight:
On December 16, 2025, at about 1050 local time, a privately-registered SilverLight American Ranger AR-1 gyroplane, N529MW, sustained substantial damage when it was involved in an accident at Colorado Air and Space Port (CFO/KCFO), Denver, Colorado. The sole pilot onboard was not injured. The local flight originated from KCFO.

According to the FAA: "Aircraft on takeoff and the main rotor struck the rudder." According to ADS-B data, the gyro was departing runway 26 when the event occurred. It entered a climbing left turn to an altitude of 6,175 ft and circled south of the airport before returning. The data cuts short as the gyro was on approach to the same runway.

Figure 1: ADS-B data

The airport field elevation was 5515.2 ft. Runway 8/26 is asphalt 8002 x 100 ft. long.

Winds at the time were from 240 at 10 knots, temperature: 15 °C, dewpoint: -7 °C, and an altimeter setting of 29.98 inches of mercury.

- Additional Information:

Two similar accidents were discovered after a review of the NTSB accident data involving the gyroplane type. ERA22LA269 and GAA20CA044, here is the analysis and probable cause from those events:

ERA22LA269

The pilot said the traffic pattern was busy, so he began the pre-rotation process as he taxied the gyroplane onto the runway to depart. At that time, the rotor disk rpm was at 140 rpm, which was 20 rpm above the recommended takeoff speed. The pilot said he slowly applied power because he had a passenger onboard, which may have allowed time for the disk speed to decay and become susceptible to blade flap. During the takeoff roll, the gyroplane's main rotor blades struck and severed the tail assembly, resulting in substantial damage. The pilot said there were no preimpact mechanical malfunctions or failures that would have precluded normal operation.

Probable Cause: The pilot's failure to monitor rotor disk speed on takeoff, which resulted in blade flapping and the main rotor blades striking the gyroplane's tail assembly.

GAA20CA044

The pilot reported that, during the takeoff roll, the gyroplane's rotor "flapped" and struck the rudder. He aborted the takeoff and taxied to the ramp without further incident. The gyroplane sustained substantial damage to the rudder. The pilot reported that there were no preaccident mechanical failures or malfunctions with the gyroplane that would have precluded normal operation. The pilot stated that if he had aborted the takeoff at the first indication of a problem the accident could have been avoided.

Probable Cause: The pilot's failure to attain the proper rotor speed before takeoff, which resulted in the rotor blade striking the rudder. A Contributing to the accident was the pilot's failure to abort the takeoff in a timely manner.

According to the FAA Rotorcraft Flying Handbook:

BLADE FLAP

On a gyroplane with a semi-rigid, teeter-head rotor system, blade flap may develop if too much airflow passes through the rotor system while it is operating at low r.p.m. This is most often the result of taxiing too fast for a given rotor speed. Unequal lift acting on the advancing and retreating blades can cause the blades to teeter to the maximum allowed by the rotor head design. The blades then hit the teeter stops, creating a vibration that may be felt in the cyclic control. The frequency of the vibration corresponds to the speed of the rotor, with the blades hitting the stops twice during each revolution. If the flapping is not controlled, the situation can grow worse as the blades begin to flex and bend. Because the system is operating at low r.p.m., there is not enough centrifugal force acting on the blades to keep them rigid. The shock of hitting the teeter stops combined with uneven lift along the length of the blade causes an undulation to begin, which can increase in severity if allowed to progress. In extreme cases, a rotor blade may strike the ground or propeller.

- Weather:

METAR KCFO 161647Z 22008KT 10SM CLR 13/M08 A2999=

METAR KCFO 161747Z 24010KT 10SM CLR 15/M07 A2998=

METAR KCFO 161847Z 27011KT 10SM CLR 19/M09 A2997=

Cirrus SR22T GTS G6 carbon, N53KH, incident occurred on December 18, 2025, at Muleshoe Municipal Airport (2T1), Muleshoe, Texas

This is preliminary information, subject to change, and may contain errors. Any errors in this report will be corrected when the final report has been completed.

https://registry.faa.gov/AircraftInquiry/Search/NNumberResult?nNumberTxt=N53KH

- History of Flight:
On December 18, 2025, at about 1300 local time, a Cirrus SR22T GTS G6 carbon, N53KH, sustained unknown damage when it suffered a left main landing gear collapse during an attempted takeoff at Muleshoe Municipal Airport (2T1), Muleshoe, Texas. The sole pilot onboard was not injured. At 1256 LT, w
inds were reported from 060° at 15 knots, gusting 18 knots.

- Weather:

METAR KCVN 181856Z AUTO 06015G18KT 10SM CLR 11/M11 A3012 RMK AO2 SLP191 T01111106 $

METAR KCVN 181956Z AUTO 06009KT 10SM CLR 11/M11 A3012 RMK AO2 SLP193 T01111111 $